Knife steels compared|Choosing a Japanese Knife
White, Blue, Ginsan, VG-10, SG2 and more: 16 knife steels compared with maker values and sources, plus lineage charts and a chef’s views.
Hardness is the steel maker’s published value with standard hardening and tempering (mostly a minimum; some are ranges or reference values). It is not the hardness of a finished knife, which depends on how the smith heat-treats the blade.
Stainless steel: at least 10.5% chromium (Cr) and no more than 1.2% carbon (C), as explained by Nippon Steel.
In my experience (chef’s view): Many stainless steels are harder to sharpen than carbon steel. That said, the maker of VG-10 calls it easy to sharpen. Harder steels tend to hold an edge longer.
White #2 (Shirogami #2)
Carbon steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.05–1.15%
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- Less hard than White #1, but tougher
- Rust
- Rusts (almost no chromium)
- Sharpening
- Easier to sharpen than Blue (the maker’s chart gives Blue “lower grindability”)
Chef’s view: A good balance of sharpness and easy sharpening, and friendly for beginners. The reference point for other steels. Reasonably priced and good enough for professional work.
Sources: S31 S1 S13 S14 S16
White #1 (Shirogami #1)
Carbon steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.25–1.35%
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- Harder than White #2 (more carbon)
- Rust
- Rusts
- Chipping
- Less tough than White #2
Chef’s view: Hard to heat-treat, so it depends on a skilled smith. Weak against impact: handle with care.
Sources: S31 S1 S6 S13 S14
White #3 (Shirogami #3)
Carbon steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 0.80–0.90%
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Rust
- Rusts
- Features
- Not confirmed (not in the maker's chart)
Sources: S31 S12 S13 S14
Yellow #2 (Kigami #2), for reference
Carbon steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.05–1.15%, P 0.030% max, S 0.006% max
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Place
- JIS SK steel with fewer impurities. With fewer still, it becomes White #2
- Rust
- Rusts
Chef’s view: Mainly for home knives and cooking schools. Professional itamae rarely use it.
Sources: S31 S1 S12 S14 S15
Blue #2 (Aogami #2)
Alloy steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.05–1.15%, Cr 0.20–0.50%, W 1.00–1.50%
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- More wear-resistant (longer edge life) than White #2
- Rust
- Rusts (Cr 0.5% or less)
- Sharpening
- Harder to sharpen than White steels (“lower grindability” in the maker’s chart)
In my experience (chef’s view): Tough: it resists chipping. Holds an edge long and leaves a smooth, beautiful cut surface.
Sources: S31 S1 S7 S13 S14 S20
Blue #1 (Aogami #1)
Alloy steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.25–1.35%, Cr 0.30–0.50%, W 1.50–2.00%
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- Harder than Blue #2 (more carbon)
- Rust
- Rusts
- Chipping
- Less tough than Blue #2
- Sharpening
- Not stated in the maker’s chart
Chef’s view: Cuts without force, so it does not crush the food. The edge lasts long, but sharpening is difficult and needs good stones.
Sources: S31 S1 S13 S14
Blue Super (Aogami Super)
Alloy steel・Proterial (Yasugi steel)
- Chemistry
- ◎ C 1.40–1.50%, Cr 0.30–0.50%, W 2.00–2.50%, V 0.30–0.50% (no Mo)
- Hardness
- ◎ HRC 60 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- The hardest and most wear-resistant in the maker’s carbon-steel chart (White and Blue). The maker’s hardness figure is the same “60 or more” as White and Blue
- Rust
- Rusts
- Sharpening
- Harder to sharpen (“lower grindability” in the maker’s chart)
In my experience (chef’s view): Barely loses its edge. Chips easily, and a chip is very hard to fix yourself.
Chef’s view: Leave it for when your sharpening skills and stones are ready.
Sources: S31 S1
Ginsan (Gin-3, Silver #3)
Stainless・Proterial (formerly Hitachi Metals)
- Chemistry
- ◎ C 0.95–1.10%, Cr 13.00–14.50%, Si 0.35% max, Mn 0.60–1.00%
- Hardness
- ◎ HRC 59 or more (Proterial’s published value, standard hardening and tempering)
- Edge
- Harder than Gin-5 (more carbon)
- Rust
- Stainless (Cr 10.5% or more)
- Sharpening
- Not confirmed (no maker statement)
In my experience (chef’s view): Easy to sharpen. Feels close to carbon steel, and cuts well.
Chef’s view: Many itamae love it.
Sources: S31 S1 S14 S16 S22
VG-10
Stainless・Takefu Special Steel
- Chemistry
- ◎ C 1.00, Cr 15.00, Mo 1.00, V 0.25, Co 1.55 (typical, %)
- Hardness
- ◎ Hardened to HRC 60 or more
- Edge
- High hardness, long-lasting edge, wear resistance (maker)
- Rust
- Excellent corrosion resistance (maker)
- Sharpening
- "Easy to sharpen" (maker)
The maker warns about imitations. Buy from a shop you trust.
Chef’s view: Well balanced and very popular. Holds an edge long.
Sources: S8
Cobalt Special (CoSP)
Stainless・Takefu Special Steel
- Chemistry
- ◎ C 1.05, Cr 16.00, Mo 1.50, V 0.25, W 0.25, Co 2.50 (typical, %)
- Hardness
- ◎ HRC 60 or more
- Features
- Special melting gives an even composition. Good corrosion resistance, wear resistance, grindability and workability (maker)
Chef’s view: A very high-end stainless. Few itamae own one.
Sources: S10
SG2 (Super Gold 2)
Powder steel・Takefu Special Steel
- Chemistry
- ◎ Not published (maker)
- Hardness
- ◎ Hardened to HRC 62 or more
- Edge
- High hardness, wear resistance (maker)
- Rust
- Excellent corrosion resistance (maker)
- Chipping
- High toughness (maker)
In my experience (chef’s view): Difficult to sharpen.
Chef’s view: Extremely sharp.
Sources: S9
ZDP-189
Powder steel・Hitachi Metals (now Proterial)
- Chemistry
- ◎ C about 3%, Cr about 20% (nominal)
- Hardness
- ◎ HRC 66–68 (at least 65 with the recommended heat treatment)
- Edge
- Very high wear resistance
- Rust
- Good corrosion resistance (tested as equal to or better than 440C)
- Place
- With about 3% C it is not stainless by the definition Nippon Steel gives (C 1.2% max). The maker’s chart lists it under “stainless types”; its notice calls it a “3C-20Cr cutlery and cold-work tool steel made by powder metallurgy”
The maker has issued a notice (2006-03-08) that, depending on use and handling, the edge can chip or break. Its impact value is lower than ATS34 and 440C. Not recommended by the finder.
Sources: S31 S2 S5
HAP40
Powder HSS・Proterial
- Chemistry
- ◎ C 1.27–1.37, Cr 3.70–4.70, Mo 4.60–5.40, W 5.60–6.40, V 2.80–3.30, Co 7.50–8.50 (%)
- Hardness
- ◎ HRC 64–67
- Features
- A powder high-speed steel with both wear resistance and toughness (maker)
- Rust
- Not stainless (about 4% Cr). The maker does not state its rust resistance
It is not stainless (about 4% Cr) and there is little information on sharpening it, so the finder does not recommend it.
Sources: S31 S3 S4 S16
AUS-8
Stainless・Aichi Steel
- Chemistry
- ◎ C 0.70–0.80, Cr 13.00–14.50, Mo 0.10–0.30, V 0.10–0.25 (%)
- Hardness
- – Reference value HRC 59.0 (Aichi Steel group company table; still being checked)
- Features
- 13% Cr steel with more carbon plus V and Mo, for more hardness and wear resistance (maker)
- Rust
- Stainless
Chef’s view: Strong against rust and easy to care for. Common in home knives. Many itamae own a gyuto in this steel (one of the steels sold as “molybdenum steel”).
Sources: S11 S32
AUS-10
Stainless・Aichi Steel
- Chemistry
- ◎ C 0.95–1.10, Cr 13.00–14.50 (%). Mo and V as in AUS-8
- Hardness
- – Reference value HRC 60.0 (Aichi Steel group company table; still being checked)
- Features
- 13% Cr steel with more carbon plus V and Mo, for more hardness and wear resistance (maker)
- Rust
- Stainless
Sources: S11 S32
SKD11 (D2 class)
Tool steel・JIS G 4404 standard (Proterial SLD is equivalent)
- Chemistry
- ◎ C 1.40–1.60, Cr 11.00–13.00, Mo 0.80–1.20, V 0.20–0.50 (%, JIS values listed by Proterial)
- Hardness
- ◎ HRC 58 or more for SLD (SKD11 class, Proterial). Not a value for SKD11 itself
- Features
- A general cold-work die steel with good wear resistance and hardenability (Proterial’s description of SLD)
- Rust
- About 12% Cr, but with more than 1.2% C it is not stainless by the definition Nippon Steel gives
Easily mistaken for stainless, so the finder does not recommend it.
Sources: S31 S3 S16 S19
Sources
- [S31] Proterial, “YSS steel search” (composition, heat treatment and hardness per grade; open each grade from “Maker’s page” on its card; this link is Blue Super)
- [S1] Proterial, "High-grade cutlery steels" (Fig. 1, Fig. 2)
- [S2] Proterial, "Important notice on cutlery steels"
- [S3] Proterial, "Cold-work die steels"
- [S4] Proterial, "Cutting tool materials"
- [S5] Hitachi Metals America, "ZDP189" (copy of the maker's sheet)
- [S6] Industrial Research Institute of Niigata Prefecture, "White #2: hardness and structure"
- [S7] Industrial Research Institute of Niigata Prefecture, "Blue #2: hardness and structure"
- [S8] Takefu Special Steel, "V-Gold 10 (VG10)"
- [S9] Takefu Special Steel, "Super Gold 2 (SPG2)"
- [S10] Takefu Special Steel, "Cobalt Special (CoSP)"
- [S11] Aichi Steel, "Stainless steels for blades"
- [S12] Tojiro (knife maker), "Types of material"
- [S13] Whetstone guide site, "Blue and White steel" (secondary)
- [S14] Personal site, "Cutlery steel grades and chemistry" (copy of Hitachi table, secondary)
- [S15] Suisin (knife maker), "White and Yellow steel"
- [S16] Nippon Steel, "Stainless steel FAQ"
- [S19] MONOist, "Tool steel basics" (secondary)
- [S20] Blue #2 composition (secondary)
- [S22] Ginsan composition (secondary)
- [S32] Aichi Techno Metal Fukaumi (Aichi Steel group), “Stainless”
A free app made by an individual itamae. Not endorsed by any maker or shop. Some links are affiliate links. Steel and product names are trademarks of their respective owners. This app is not endorsed by any manufacturer or store.